Track and running insoles for sprint spikes and training shoes
Same athlete. Same spikes. Springbak® beneath your feet—from the starting blocks to the finish line.
Choosing insoles for track spikes or training shoes starts with checking the space inside your own pair. Springbak® Springsoles add a patented 3/32-inch resilient 1,4-polybutadiene layer to compatible footwear for sprinting, hurdles, field-event training and training runs in your running shoes. The material is designed to compress under load and return toward its shape; energy returned to the athlete, sprint speed and next-stride performance have not been directly measured. Use the spike-fit guidance and installation video below before choosing your size.
- 3/32"
- 3/32-inch total thickness — designed to minimize changes to spike and racing-flat fit; confirm fit in your own footwear.
- 2x+
- Force required to displace a person standing on Springsoles in Weber State testing — a standing-stability measurement, not a direct measure of sprint, hurdle or jump performance.
- 4
- U.S. patents behind the Springsole design

“Small advancements in athletic footwear can translate into meaningful gains on the track. That is the space Springbak works in.”
What track & field demands of your feet
- Very short ground contacts at top-end speed
- Block starts that demand maximum force into the track in one direction
- Approach runs and takeoffs in long, triple and high jump
- Hurdle touchdowns that land and re-accelerate in the same instant
- Hundreds of tempo reps per week on a hard synthetic surface
- Throwers planting repeatedly on a rigid concrete ring
Why Springsoles fit this sport
Built for short ground contacts
A thin, resilient 1,4-polybutadiene layer designed for repeated short, high-load contacts in sprinting. This is an intended design application; contact time and energy return to the athlete have not been directly measured.
Spike-compatible profile
At 3/32 of an inch, Springsoles are designed to minimize changes to the spike setup you already train and race in. Try the Springsole untrimmed first. The 3/32-inch layer is designed to minimize changes to fit. Confirm flat placement, lockdown, lace tension, spike fit and any brace compatibility in your own footwear before training or competition.
Measured standing stability
Weber State force plate testing: more than twice the force was required to displace a person standing on Springsoles. That test measured standing resistance to displacement — not sprint, hurdle or jump performance. Plants and touchdowns are intended applications, not measured outcomes.
Designed for repeated training volume
Tempo, accelerations and hill work add up fast. Springsoles are a thin resilient layer designed for repeated track-and-field use across a long training block.
The technology, materials and four U.S. patents behind Springsoles are detailed on How it works.
Best insoles for track spikes: what to compare
No insole is the best for every athlete or every spike. These are the things you can actually check before you buy any track insole, including ours.
Thickness
A sprint spike has almost no room inside. A few millimetres can change heel height and lacing pressure. Springsoles are 3/32 inch (about 2.4 mm).
Works with a sewn-in pad
Most spikes have a pad stitched or glued in. A Springsole goes on top of it, printed side up. Never cut, peel or force the pad out.
Full length, not heel-loaded
Sprinting puts you on the front of the foot. Thick heel cushions and wedges can push the heel up in the counter. Springsoles are one even, full-length layer.
Material that holds its shape
Tempo days, block starts and jump plants add up. Look for material that returns to shape instead of packing flat. Springsoles use a resilient 1,4-polybutadiene elastomer.
What was actually measured
Ask what was tested, where and by whom. For Springsoles, Weber State measured standing stability, not sprint speed, block starts or jump distance. Coach reports are their own observations.
Trimming and testing
Order your regular size and try it untrimmed first. Trim only the toe or forefoot in very small amounts, never the heel. Do warm-ups and one full-speed rep before you race in them.
Use these checks to compare any track insole. Every spike is different, so confirm the fit in your own pair.
See it, then test it
See the Springbak® Difference in Action
How patented Springbak® technology is designed to work beneath the athlete's foot during running, jumping, lifting, and cutting.
The Springbak® Legacy Film
Filmed at Northstar Studios in Nashville: founder Bill Crow's vision, 20 years of R&D, and the athletes, coaches and researchers who tested it.
Where it shows up on the track



Fit check for track & field footwear
This is the sport where the fit check matters most. Many spikes have a sewn-in pad rather than a removable insole; the Springsole sits on top of that pad, trimmed to the outline. Spikes with a removable insole take it underneath. Trainers and flats follow the normal removable-liner rule. Verdicts by spike model are below.
| Shoe | Verdict |
|---|---|
| Nike Air Zoom Maxfly / Maxfly 2Elite sprint spike, 100m–400m | Expected fit: toe trimming may be needed |
| Nike Zoom Superfly Elite 2Elite sprint spike | Expected fit: toe trimming may be needed |
| Nike Zoom Rival Sprint / Rival MultiTraining and high-school sprint / multi-event spike | Expected fit: try untrimmed first |
| Nike Zoom Ja Fly 4Sprint spike, lightweight last | Expected fit: toe trimming may be needed |
| adidas Adizero Prime SP2Elite sprint spike | Expected fit: toe trimming may be needed |
| adidas SprintstarTraining and school-level sprint spike | Expected fit: try untrimmed first |
| adidas Adizero Finesse (middle distance)800m–1500m spike | Expected fit: try untrimmed first |
| Puma evoSPEED Sprint / Future Faster+Sprint spike | Expected fit: toe trimming may be needed |
| ASICS Metasprint / Hyper SprintSprint spike (Metasprint is pinless) | Expected fit: toe trimming may be needed |
| New Balance MD-X / SD-XMiddle distance and combined-events spike | Expected fit: try untrimmed first |
| Any brand Trainers, racing flats and warm-up shoesEverything that is not a spike | Expected fit: try untrimmed first |
Install chart
How to install Springsoles in a track spike
Track spikes are often different from trainers: many have a thin pad stitched or glued into the shoe, but construction varies, so check your own pair. If the liner is removable, try the Springsole underneath it; if it is lightly glued, remove it only if it releases cleanly. If it tears, stretches, deforms or resists removal, stop, leave it in place and put the Springsole on top. Try the Springsole untrimmed first — the 3/32-inch layer is designed to minimize changes to fit. Confirm flat placement, lockdown, lace tension, spike fit and any brace compatibility in your own footwear before training or competition.
1. Your foot / sock
Sits straight onto the Springsole. Nothing else goes between them.
2. Springbak® Springsole
3/32"Drop it in here — on top, printed side up, heel seated all the way back.
3. Sewn-in factory pad
Stitched or glued into the spike. Leave it alone — do not cut, peel or pry it out.
4. Spike plate and pins
Not altered by the Springsole. The 3/32-inch layer is designed to minimize changes to how the spike feels — confirm actual fit in your own pair.
Same order for racing flats with a stitched-in footbed. In trainers with a loose, removable insole, the Springsole goes under that insole instead.
| Step | Do this | Not this |
|---|---|---|
| Step 1Check the shoe | Try the Springsole without trimming. Check whether the liner is removable. A lightly glued liner may release with a gentle, steady pull; stop if it starts to tear, stretch or deform. | Never force out a firmly bonded or stitched liner. |
| Step 2Drop it on top | Lay the Springsole into the spike on top of the sewn-in pad, printed side facing up toward your foot. | Do not try to slide it underneath the pad or the plate. |
| Step 3Seat the heel | Push it back until the Springsole heel is flush with the heel of the spike, then smooth it flat from heel to toe. | Do not leave it bunched forward or riding up the heel counter. |
| Step 4Trim if long | Only if needed, remove a very small amount from the toe or forefoot, reinsert it and check before cutting more. | Never trim the heel, unnecessarily narrow the sides, alter the heel shape or cut more than needed. |
| Step 5Lace and test | Lace as normal, then jog, do build-ups and one full-speed rep. It should feel like your spike with a firmer, livelier floor. | Do not debut them in a race without a session in them first. |

Watch it
Dropping a Springsole into a track spike (5 seconds)
A close-up of the only move that matters in a sprint spike: the Springsole is laid flat on top of the shoe's sewn-in footbed, printed side up, then pressed smooth from heel to toe. Nothing is removed, cut or pried out of the shoe.
Full transcript
- 0:00
- A white sprint spike sits on a red track, laces open. The factory footbed is a thin pad stitched into the shoe, so nothing is lifted out or removed at any point in this clip.
- 0:01
- A hand holds a thin black Springbak Springsole, printed side up, above the shoe and lines the heel of the insole up with the heel of the spike.
- 0:02
- The Springsole is lowered flat onto the top of the sewn-in footbed — on top of the pad, not under it — and slid back until the heel seats fully into the heel cup.
- 0:03
- Fingers press the insole smooth from heel to toe so it lies flat with no bubble, wrinkle or curled edge along the sides of the shoe.
- 0:04
- The forefoot is checked: the Springsole ends at the toe of the shoe. If it overhangs, it is trimmed at the toe only, following the outline of the factory pad.
- 0:05
- The spike is laced normally over the installed Springsole, ready for build-ups and one full-speed rep before it is used in a race.
Full sizing guide, trimming instructions and fits-as-is verdicts → /catalog
Insole vs. midsole layer
Spikes have almost no midsole by design, and many have a sewn-in pad instead of a removable insole. That is exactly why a replacement insole is the wrong tool: there is nothing to replace, and extra foam defeats the spike. Springbak® Springsoles are a thin, resilient-rubber midsole layer that sits on top of a fixed pad or under a removable one, adding structured response without raising the foot or changing pin angle. The plate, the pins and the fit of the upper are untouched. Same spikes, same blocks — with a layer underneath built to return force at full speed.
Read the full insole-vs-midsole explainer → /how-it-works
Weber State force plate testing
What the force-plate result does — and does not — show for track
Weber State University force plate testing: more than twice the force was required to displace a person standing on Springsoles. That test measured standing resistance to displacement (standing stability). It did not directly measure sprint speed, block starts, ground-contact time, hurdle or jump performance, landing forces, spike geometry, energy returned to the athlete, injury or fatigue.
See the full breakdown on Proof & testing.
Force-Plate Stability Study
In force-plate testing, subjects standing on Springbak® Springsoles showed more than twice the overall resistance to being pushed from their position.
In plain English: they were harder to move. They could hold their ground better against a sideways push—exactly the kind of stability athletes need when planting, cutting, jumping, landing, and absorbing contact.
Springbak® gives the foot a more stable, responsive platform to work from inside the shoe.
Results are from the force-plate testing described in U.S. Patent No. 6,589,630 B1. Individual results vary.
More athlete results → /testimonials · Study details → /proof · Try the core challenge → /edge/the-springbak-challenge
FAQ
Track & Field insoles — frequently asked questions
Fitting a pair for spikes or a full training block? See the full track and field insoles FAQ.
What are the best insoles for sprinters?
+
When choosing insoles for running spikes, sprinters typically look for the thinnest layer that is still designed to return energy — thicker or softer inserts can take up internal volume and are generally built to cushion rather than rebound, though specifications vary by model. Springbak® Springsoles are 3/32" of 1,4-polybutadiene, designed to minimize changes to spike fit and to return energy at contact; sprint performance and athlete energy return have not been directly measured.
Can you put insoles in track spikes?
+
Yes, even when the insole does not come out — that is the normal case. Many sprint spikes have a thin pad sewn or glued into the shoe, but construction varies — check your own pair. If the pad does not lift out cleanly, leave it in place and put the Springsole on top of it, directly under your foot, printed side up. Nothing gets removed and nothing goes under the pad. The 3/32-inch layer is designed to minimize changes to spike volume — try it untrimmed first and confirm actual fit, flat placement and lockdown in your own pair.
How do I tell if my shoe has a removable insole or a sewn-in pad?
+
Reach in and tug the footbed at the heel. If it lifts out it is removable, and the Springsole goes underneath it. If it is stitched or glued down it is a sewn-in pad — which is what nearly every sprint spike uses — and the Springsole goes on top.
Can I cut or peel the sewn-in pad out of my spikes first?
+
No. Cutting or peeling a stitched-in footbed damages the upper and the plate bond and is not needed — the Springsole is designed to sit on top of it. Trim only the Springsole itself if needed, and only at the toe or forefoot: small passes, tracing your own foot outline until it lies flat in a narrow sprint last. Never trim the heel or unnecessarily narrow the sides, and recheck the fit after each small trim.
Will my spikes feel too tight with a Springsole on top of the pad?
+
Try the Springsole untrimmed first. The 3/32-inch layer is designed to minimize changes to fit. Confirm flat placement, lockdown, lace tension, spike fit and any brace compatibility in your own footwear before training or competition. If your spikes are already race-snug, trim only at the toe or forefoot in very small amounts, rechecking the fit after each trim.
Does the Springsole move around inside a spike at full speed?
+
It is designed to stay put when the heel is seated all the way back and the surface is pressed flat from heel to toe. Lace as normal, then jog, do build-ups and one full-speed rep to confirm it stays in place in your own spike before you race in them.
Do they change my spike fit or pin angle?
+
Try the Springsole untrimmed first. The 3/32-inch layer is designed to minimize changes to fit. Confirm flat placement, lockdown, lace tension, spike fit and any brace compatibility in your own footwear before training or competition. Trim only if needed for a flat fit — start at the toe or forefoot in very small amounts.
Will they help my block start?
+
Springsoles do not create force, and block-start performance has not been directly measured. They are a thin resilient layer designed for repeated sprint use. Pair them with the speed program in Train for the actual force development.
Are they legal in sanctioned track competition?
+
They are an insole inside your shoe, not an assisting device attached to it. We are not aware of any federation rule against them, but confirm with your meet officials.
Do jumpers and throwers benefit as much as sprinters?
+
Springsoles are designed for repeated track-and-field use across event groups. Athletes looking for insoles for hurdlers or long jump insoles use the same 3/32-inch layer — hurdle touchdowns, jump plants, throwing-ring plants and distance volume are intended applications. Event-specific outcomes have not been directly measured, and individual results vary.
Will they help with shin splints or sore feet during a heavy block?
+
Springsoles are not a medical device and are not designed to treat or prevent shin splints or any condition. They are a thin resilient layer designed for repeated track-and-field use. If you have pain, see a qualified clinician.
Can I use Springsoles as running insoles in my trainers, flats and warm-up shoes?
+
Yes. Running shoes and trainers usually have a loose insole. Lift it out, lay the Springsole flat on the footbed, then put the insole back on top — the opposite order from a spike. If the insole is firmly glued or stitched down, never force it out; put the Springsole on top instead. Distance-running performance has not been directly measured.
Springbak® Springsoles
Checking price…Ships from the USA · 30-day no-questions-asked returns
Team pricing for schools, clubs and collegiate programs
Outfit a full sprint squad, jumps crew or distance group with Springbak® Springsoles. We offer volume pricing, invoice billing and fast turnaround for verified track & field programs.
Team pricing and bulk orders → /shop#team-form
Train for track & field
Sprint Mechanics & Top Speed
Six weeks of technical sprinting for track athletes: block clearance, transition, and holding form at 95 percent.
Open programHurdle Rhythm & Trail-Leg Speed
Seven weeks of touchdown timing, lead-leg speed and trail-leg mechanics for sprint hurdlers who lose the race between hurdles.
Open programSpeed & Acceleration
Six weeks of short, sharp work aimed at footplant time and stride length — the two levers that actually move a 40 time.
Open programFirst-Step Quickness
Four weeks of reactive starts, decel work and hip control for guards, receivers and anyone who wins with the first two steps.
Open program
Read more on The Edge
All Edge articlesSpringbak® — MADE IN THE USA. Individual results vary.
Last updated 2026-08-26.