Springbak® official logo

Volleyball insoles for jumping, blocking and court movement

Same player. Same shoes. Springbak® beneath your feet—from the opening serve to match point.

Springbak® Springsoles are a thin 3/32-inch resilient layer used with your existing factory insole rather than replacing it. They are designed for the movements volleyball repeats — approaches, blocks, landings and lateral court movement — where the material is built to return to shape between reps instead of packing out like foam. Coaches at Minnesota, Nebraska, BYU, UC Santa Barbara and the New Zealand men's national team have all put them on their rosters. The layer is designed to minimize changes to your shoe's original fit — confirm fit in your own footwear.

2x+
force required to displace a person standing on Springsoles in Weber State stability testing — not a direct measure of vertical-jump height, energy return, landing-force reduction or volleyball performance
≈5%
faster spiking speed reported by Hugh McCutcheon from his BYU speed-gun session
3/32"
thin layer designed to minimize changes in court-shoe and ankle-brace fit
4
U.S. patents behind the material
Volleyball outside hitter at the peak of an approach jump, arm cocked to spike above the net
Coaches’ circle →

Three coaching legends put Springsoles on their rosters

These are attributed coach reports and observations from teams that used Springsoles. Hugh McCutcheon's report comes from his BYU speed-gun session; the other published quotes remain each coach's own observation and appear exactly as Springbak has always run them.

  • Hugh McCutcheon holding a volleyball on the Minnesota court

    Hugh McCutcheon

    Minnesota / USA Volleyball

    Former head coach, University of Minnesota volleyball; former USA Volleyball head coach; assistant coach at BYU when he tested Springsoles

    Olympic gold (2008 men) and silver (2012 women) as USA head coach

    “While an assistant coach at BYU I tested spiking speed of our men's volleyball team with a speed gun. After an hour of testing it became apparent that they were hitting 5% faster in Springsoles.”

    Hugh McCutcheon reported the approximately 5% faster spiking figure from that speed-gun session at BYU; it was not a vertical-jump measurement.

  • John Cook wearing a Nebraska polo shirt

    John Cook

    Nebraska volleyball

    Former head coach, University of Nebraska volleyball

    Four NCAA national championships at Nebraska

    “There is no doubt in my mind after testing and hearing the athlete's feedback that your innersoles help our athletes jump higher and move quicker.”

    A coach's reported observation from his program's own testing and athlete feedback — not a laboratory measurement. Individual results vary.

  • Portrait of volleyball coach Carl McGown

    Carl McGown

    BYU men's volleyball

    Former head coach, BYU men's volleyball (1990–2002); longtime USA Volleyball national-team coach

    Two NCAA national championships at BYU (1999, 2001); Volleyball Hall of Fame

    “We love Springsoles from Springbak®. We have been using them for an explosive team.”

    In memoriam — Carl McGown passed away December 30, 2016, at age 79. A coaching icon whose technique teaching shaped generations of American volleyball.

Quotes as published on springbak.net. Coaching titles reflect the programs these coaches led; endorsements are personal and do not imply endorsement by any university, athletic department or national federation. Coach photographs are Springbak's own testimonial images as published on springbak.net; university marks visible in them belong to their respective schools. Individual results vary.

What volleyball demands of your feet

  • Approach jumps and block jumps, over and over, in the same spot
  • Repeated hard landings on an unforgiving court
  • Lateral defensive movement and floor work
  • Multi-match tournament days

Why Springsoles fit this sport

Designed for repeated jump volume

The resilient layer is designed for repeated approaches, blocks and landings; the standing force-plate test did not measure landing-force reduction or late-match performance.

Insoles for volleyball shoes without bulk

At 3/32", these volleyball shoe inserts are designed to minimize changes in shoe fit; confirm the actual fit and ankle support in your own court shoes.

Returns to shape between jumps

The resilient material returns to shape between repetitions instead of packing out like foam. How each jump feels depends on the athlete — late-match performance was not measured.

The technology, materials and four U.S. patents behind Springsoles are detailed on How it works.

Best insoles for volleyball: what to compare

No insole is the best for every player. These are the things you can actually check before you buy any volleyball insole, including ours.

Thickness

Court shoes are built low and snug. Anything much over 1/8 inch can change how the shoe fits. Springsoles are 3/32 inch.

Works with your liner

Full-length replacement insoles take the place of your shoe's own footbed. Springsoles go with it: under a removable liner, or on top of a liner that doesn't release cleanly. Never force a glued liner out.

Fit with ankle braces

Many players wear braces. Check lace tension, lockdown and brace fit in your own shoes before you play, whatever insole you choose.

Material that holds its shape

Volleyball means jump after jump. Look for material that returns to shape instead of packing out. Springsoles use a resilient 1,4-polybutadiene elastomer.

What was actually measured

Ask what was tested, where and by whom. For Springsoles, Weber State measured standing stability, not jump height. Coach reports are their own observations.

Trimming and sizing

Order your regular court-shoe size and try it untrimmed first. Trim only the toe or forefoot in very small amounts, and never the heel.

Use these checks to compare any volleyball insole. Every shoe is different, so confirm the fit in your own pair.

Fit check for volleyball footwear

Check the liner in your own volleyball shoes. Try the Springsole untrimmed first, underneath a removable liner or on top of one that resists gentle removal. Confirm flat placement, heel position, toe clearance, lockdown and ankle-brace compatibility; unchanged fit or brace clearance is not guaranteed. Expected-fit guidance for common models appears below.

Springsole fit verdicts for common volleyball shoes
ShoeVerdict
Mizuno Wave Lightning Z8Low-profile attacker / all-around indoor shoeExpected fit: toe trimming may be needed
Mizuno Wave Momentum 3 / 4Stability-leaning indoor shoe for hitters and blockersExpected fit: try untrimmed first
Mizuno Wave Supersonic 3Lightweight quick-transition indoor shoeExpected fit: toe trimming may be needed
ASICS Sky Elite FF 3Elite jump-focused indoor shoeExpected fit: try untrimmed first
ASICS Gel-RocketValue indoor court shoe, thin factory footbedExpected fit: try untrimmed first
ASICS Netburner Ballistic FF 4Supportive indoor shoe for high-volume jumpersExpected fit: try untrimmed first
adidas Crazyflight 2026 / Crazyflight 7 MidIndoor jump shoe, low and mid-cut versionsExpected fit: try untrimmed first
adidas Crazyflight X LOVBTeam / league colorway of the Crazyflight platformExpected fit: try untrimmed first
Nike Air Zoom HyperAce 3Indoor court shoe with a forefoot air unitExpected fit: try untrimmed first
Nike React HyperSet 2All-around indoor shoe with a foam midsoleExpected fit: try untrimmed first
Under Armour Jet '26Court / crossover basketball-volleyball shoeExpected fit: try untrimmed first

Watch it

Installing a Springsole in a volleyball shoe (20 seconds)

Filmed courtside in two close-up scenes: the factory insole lifts out, the black Springbak-branded Springsole slides in flat against the midsole, then your own insole goes right back in on top of it and is pressed flat. The video shows a shoe with a removable liner: the Springsole is tried untrimmed, placed underneath, and checked flat. Other liner types follow the fitting steps below.

Full transcript
0:00
This example shoe has a removable liner. First try the Springsole untrimmed, then lift the grey factory liner out and set it beside the shoe.
0:03
Step 2 — Insert: hands slide the black Springbak Springsole — yellow Springbak script and springbok logo facing up — into the shoe, flat against the midsole, lining the heel of the insole up with the heel of the shoe.
0:06
Thumbs press the black Springsole smooth from heel to toe so it lies flat — no bubble, no wrinkle, no curled edge.
0:10
Step 3 — Layer on top: the grey factory insole is lowered back into the shoe so it sits directly on top of the black Springbak Springsole.
0:14
Fingers press the factory liner flat. Trim only if needed, removing a very small amount from the toe or forefoot and checking after each cut. Never trim the heel.
0:17
The finished stack: black Springbak Springsole on the bottom, your own insole on top, and the shoe laced up snug. Under a minute per shoe.
Download transcript (.txt)

Full sizing guide, trimming instructions and fits-as-is verdicts → /catalog

Insole vs. midsole layer

Volleyball shoes are cushioned for landings; aftermarket insoles usually just add more cushion, which can leave you sitting higher in the shoe and slower off the floor. A midsole layer does the opposite job. Springbak® Springsoles are a thin, resilient-rubber layer that fits beneath the stock liner, or on top of a glued-in one, so the shoe you block and hit in gains a layer that returns force on every approach, landing and lateral push. Your ankle brace still fits, your heel still sits where it did, and the shoe's own cushioning is unchanged. Same shoes, same approach — with a midsole layer under every jump.

Read the full insole-vs-midsole explainer → /how-it-works

On the record

What volleyball coaches found

Published, attributed observations from coaches whose rosters used Springsoles. These testimonials are personal reports, not the Weber State standing force-plate measurement. Individual results vary.

“While an assistant coach at BYU I tested spiking speed of our men's volleyball team with a speed gun. After an hour of testing it became apparent that they were hitting 5% faster in Springsoles.”
Hugh McCutcheonFormer head coach, University of Minnesota volleyball; Olympic gold-medal head coach, USA Volleyball

Weber State force plate testing

The measured force-plate result and its volleyball application

Measured laboratory result: Weber State University force-plate testing found that it took more than twice the force to displace a person while standing on Springsoles. That test measured standing stability, not vertical-jump height, landing forces, injury prevention or late-match performance. Volleyball application: the resilient Springsole layer is designed for the plants, jumps, landings and changes of direction used in play; this is a product explanation, not an outcome measured by the force-plate test.

  • Measured: more than twice the force was required to displace a person standing on Springsoles.
  • Product application: a resilient layer beneath the foot during approach steps and landings.
  • Material explanation: the elastomer is designed to return to shape between repetitions instead of packing out like foam.

See the full breakdown on Proof & testing.

Force-Plate Stability Study

In force-plate testing, subjects standing on Springbak® Springsoles showed more than twice the overall resistance to being pushed from their position.

This was a standing stability measurement. It did not measure vertical-jump height, landing forces, injury prevention, or late-match performance.

For volleyball, Springbak® applies that resilient platform beneath the foot during plants, jumps, landings, and changes of direction; those applications are product explanations, not outcomes measured in the force-plate test.

Results are from the force-plate testing described in U.S. Patent No. 6,589,630 B1. Individual results vary.

More athlete results → /testimonials · Study details → /proof · Try the core challenge → /edge/the-springbak-challenge

FAQ

Volleyball insoles — frequently asked questions

Will volleyball insoles help my approach jump?

+

Springbak is designed to return energy you generate rather than create force. Some hitters report feeling more spring late in matches; that is attributed user feedback, not a measured endurance result. Hugh McCutcheon reported approximately 5% faster spiking speed from his BYU speed-gun session. Separately, Weber State laboratory force-plate testing found that it took more than twice the force to displace a person while standing on Springsoles; that test did not measure vertical-jump height. Individual results vary.

What are the best insoles for volleyball players?

+

When you shop for volleyball performance insoles, look for a thin, high-resilience layer that sits with your factory liner rather than replacing it. The 3/32-inch Springsole is designed to minimize changes in shoe fit, but players should confirm lockdown, lace tension and ankle-brace fit in their own footwear. Full-length replacement insoles change the fit of a low-profile court shoe and are usually built for arch support, not energy return. Springsoles were adopted on rosters at Minnesota, Nebraska, BYU, UC Santa Barbara and the New Zealand men's national team.

Do volleyball insoles actually improve performance?

+

An insole cannot create force; Springbak is designed to return part of the energy an athlete produces. The evidence here is distinct: Weber State University laboratory force-plate testing found that it took more than twice the force to displace a person while standing on Springsoles. Separately, coach Hugh McCutcheon reported approximately 5% faster spiking speed during his BYU speed-gun session. Neither finding directly measured vertical-jump height, landing-force reduction, injury prevention or late-match performance. Individual results vary.

What is the difference between a Springbak® layer and a carbon-plate insert?

+

A plate insert is rigid and full-length: it stiffens the shoe, adds height and changes how the forefoot bends, which is why plate products are thick and shoe-specific. A Springsole is a 3/32" patented elastomer layer designed to preserve your shoe's own geometry while returning energy through the material instead of a stiff lever; confirm the actual fit in your own pair. For volleyball, where court shoes are deliberately low and ankle braces are common, keeping changes to the original fit to a minimum is usually the deciding factor.

Are Springsoles legal under NFHS, NCAA and USA Volleyball rules?

+

Yes. They are an insole that sits inside the shoe — not a device attached to it — and add no external spring, plate or device attached to the shoe. They have been used on rosters at Minnesota, Nebraska, BYU, UC Santa Barbara and the New Zealand men's national team. Rules bodies restrict what is attached to or worn outside a shoe, not what liner you play on. If your conference or state association has its own equipment approval process, show them the insole itself — it looks and installs like a footbed.

Do they work with ankle braces?

+

The thin 3/32-inch layer is designed to minimize changes in shoe fit. Confirm the actual lace tension and ankle-brace fit in your own volleyball shoes before playing.

Will they raise me out of my volleyball shoes?

+

The 3/32-inch layer is designed to minimize changes in shoe fit. Confirm the actual fit, lace tension and ankle-brace fit in your own volleyball shoes before playing.

How do I install them in court shoes?

+

Try the Springsole untrimmed first. If the factory liner is removable, lift it out, lay the Springsole flat underneath and reinstall the liner. If the liner is lightly glued, remove it only if it releases cleanly with gentle, steady pressure — if it tears, stretches, deforms or resists, stop and place the Springsole on top instead; never force out a firmly bonded or stitched liner. Trim only if needed for a flat fit: very small amounts from the toe or forefoot, reinserting and rechecking after each trim. Never trim the heel or unnecessarily narrow the sides.

How many jumps will they last?

+

The patented elastomer is chosen for resilience, not foam-style compression, so it returns to shape between reps instead of packing out. Programs typically run a pair through a full club and school season of jump volume.

Do they help liberos and defensive specialists, or just hitters?

+

Every position loads the forefoot. Springbak is designed for the lateral push-offs, low lunges and repeated floor work defensive players perform. The Weber State result measured resistance to displacement while standing; it did not directly measure cutting or vertical jumping.

Do they work for both indoor and beach players?

+

Indoor players get the full benefit in court shoes. Beach players use them in trainers for lifting, approach work and conditioning, since sand play is barefoot.

What size Springsole should I order for volleyball?

+

Order your regular court-shoe size and try the Springsole untrimmed first: US men's 6/7, 8/9 and 10/11; US women's 7/8, 9/10 and 11/12; EU 38/40, 41/42 and 43/45; UK 5/6, 7/8 and 9/10. If needed, trim only the toe or forefoot in very small amounts and recheck after every cut. Never trim the heel or unnecessarily narrow the sides.

Springbak® Springsoles

Checking price…
View current price on springbak.net

Ships from the USA · 30-day no-questions-asked returns

Team pricing for volleyball clubs, high schools and collegiate programs

Outfit a full roster — every athlete plays in a different shoe, and Springsole size ranges cover the roster. Try each pair untrimmed and trim only if needed, and reach out for volume pricing and invoice billing on verified team orders.

Team pricing and bulk orders → /shop#team-form

Train for volleyball

Read more on The Edge

All Edge articles

Springbak® — MADE IN THE USA. Individual results vary.

Last updated 2026-08-26.

Four U.S. patents. Force-plate tested. → /patents · /proof